1. Before starting, please check all parts of the mechanical system carefully and make sure they are in good condition before starting.

2.在開始之前，必須將攪拌棒置于“中性”位置。

2. Before starting, the mixing bar must be placed in the "neutral" position.

3.啟動后，必須將攪拌棒置于“卸載”位置，并排掉缸內的水。

3. After starting, the mixing rod must be placed in the "unloading" position and the water in the cylinder must be drained.

4.充電時，必須將攪拌棒置于“裝載”位置。

4. When charging, the mixing rod must be placed in the "loading" position.

5.運輸之前，必須將卸料斜槽固定在“驅動”位置，以防止晃動。

5. Before transportation, the discharge chute must be fixed in the "drive" position to prevent shaking.

6.操作操縱桿時，在“空檔”位置稍停，然后移至下一個位置。

6. When operating the control lever, stop in the "neutral" position for a while, and then move to the next position.

7.抓好文明建設，桶內多余的材料不得倒塌。卸下后，您需要清潔攪拌桶，斜槽，惰輪等。

7. Pay attention to the civilization construction, and the surplus materials in the barrel shall not collapse. After unloading, you need to clean the mixing drum, chute, idler, etc.

8.一旦有人進入氣瓶以取下車門，就必須關閉車輛，拔出電動門鑰匙，并監控氣瓶的外部。

8. Once someone enters the cylinder to remove the door, the vehicle must be shut down, the key of the electric door must be removed, and the outside of the cylinder must be monitored.

如何降低流動攪拌車上料一體車的噪音

How to reduce the noise of mobile mixer

1.如果濾芯堵塞并且吸油困難或不足，請清潔或更換濾芯。

1. If the filter element is blocked and the oil absorption is difficult or insufficient, please clean or replace the filter element.

2.更換低粘度液壓油，因?yàn)樵撘簤河筒缓线m或油的粘度太高。

2. Replace the low viscosity hydraulic oil, because the hydraulic oil is not suitable or the viscosity of the oil is too high.

3.燃油箱中的液位過低，油位空氣被吸入泵中，并添加了相同數量的液壓油。

3. The liquid level in the fuel tank is too low, the oil level air is sucked into the pump, and the same amount of hydraulic oil is added.

4.吸入或吸入管路；請勿吸入空氣，檢查并擰緊。

4. Inhale or inhale pipeline; do not inhale air, check and tighten.

5.泵安裝支架的剛性不足，在工作過程中會產生振動和噪音。

5. The rigidity of the pump mounting bracket is not enough, which will produce vibration and noise in the working process.

6.輸入法蘭與傳動軸之間的連接，傳動軸與取力器之間的連接角度太大或松動時會產生噪音，請檢查緊固情況。

6. The connection between the input flange and the transmission shaft, the connection angle between the transmission shaft and the power take-off is too large or loose, which will produce noise. Please check the fastening condition.

7.儲罐中有粘附的混凝土沉積物，需要清理鏟子。

7. There is adhesive concrete deposit in the storage tank, so the shovel needs to be cleaned.

本文由水泥自動攪拌車整理發布，您是不是對這些內容有所了解了呢?更多的內容請點擊：http://www.sansungmobile.cn我們會有更多精彩內容等你查看。

This article is organized and released by Zhongke concrete mixer. Do you know something about these contents? For more information, please click: http://www.sansungmobile.cn We'll have a lot more to see.