在設備實際操作運行過程中，自動攪拌車的變速器是一個非常重要的部件。因此，我們在使用過程中對其油質需要有一定的檢測工作，那么我們具體應該怎么進行操作呢？

In the actual operation of the equipment, the transmission of the automatic mixer is a very important component. Therefore, we need to have a certain detection of its oil quality in the process of use, so how should we operate?

1、將自動攪拌車停放在水平地面上，并拉緊手制動。

1. Park the automatic mixer on a level ground and tighten the hand brake.

2、讓發動機怠速運轉數分鐘。

2. Allow the engine to idle for several minutes.

3、踩住制動踏板，將操縱手柄撥至倒擋、前進擋等位置，并在每個擋位上停留幾秒鐘，使液力變矩器和所有換擋執行元件中都充滿液壓油。將操縱手柄撥至停車擋位置。

3. Step on the brake pedal, turn the joystick to the reverse gear, forward gear and other positions, and stay in each gear for a few seconds, so that the hydraulic torque converter and all shift actuators are filled with hydraulic oil. Turn the joystick to the parking position.

4、從加油管內撥出自動變速器油尺，將擦干凈的油尺全部插入加油管再拔出，檢查油尺上的油面高度。

4. Pull out the automatic transmission dipstick from the filler pipe, insert all the cleaned dipsticks into the filler pipe and then pull them out, and check the oil level on the dipstick.

5、攪拌車發動機很熱時，切勿開啟散熱器蓋。不然很有可能會造成 迸濺的冷卻液或熱蒸氣焚燒。攪拌車發動機制冷后，保證冷卻液液面在滿和低中間。要是沒有，您須要加上蒸溜水或礦泉水或冷卻液。

5. Do not open the radiator cap when the mixer engine is very hot. Otherwise, it is likely to cause splashed coolant or hot steam to burn. After the mixer engine is cooled, ensure that the coolant level is between full and low. If not, you need to add distilled water or mineral water or coolant.

兌水后液體的相對高度不可超出滿水量。假如發覺冷卻液在短期內快速降低，則自上料式混凝土攪拌車檢查數據應查驗制冷系統是不是外泄或查驗服務點。

The relative height of the liquid after mixing with water shall not exceed the full water volume. If it is found that the coolant decreases rapidly in a short time, the inspection data of the self loading concrete mixer should check whether the refrigeration system leaks or check the service point.

在對自動攪拌車變速器進行檢查或故障診斷前，首先要對變速器油面和油質進行檢查。把選擋手柄放在P位，將發動機在怠速時至少運轉數分鐘，油液達到正常工作溫度，攪拌車須停放在水平路面上，這樣才能確保在差速器和變速器之間的油面高度正常、穩定。

Before the inspection or fault diagnosis of the automatic mixer transmission, the oil level and quality of the transmission should be checked first. Put the gear selector handle in position P, run the engine at idle speed for at least a few minutes, the oil reaches the normal working temperature, and the mixer must be parked on a horizontal road, so as to ensure that the oil level between the differential and the transmission is normal and stable.

自動攪拌車變速器油質的檢測方式便是以上內容了，希望能夠給您好的幫助吧，更多關于攪拌車使用的事項就來關注我們網站http://www.sansungmobile.cn吧！

The oil quality detection method of automatic mixer transmission is the above content. I hope I can help you. For more information about the use of mixer, please pay attention to our website http://www.sansungmobile.cn Come on!