自動攪拌車存在抱軸及悶機跳閘現象的原因必要及時找到，不然故障一旦不及時解決，隨著時間越拖越久，就會導致問題的嚴重性越來越大，下面小編為您解答。

It is necessary to find out the cause of the axle holding and the machine blocking tripping of the automatic mixer in time, otherwise, if the fault is not solved in time, it will lead to the problem becoming more and more serious as time goes on. Here are some answers for you.

自動攪拌車存在抱軸現象原因：

Reasons for axle holding of automatic mixer:

1.可能是拌和主機進水管與沖水方位原因。沖水點方位和沖刷方向不正確的話，也或者是沖水壓力過低，導致水在進入主機內部后，不能將暫時粘結在軸上的混凝土沖刷掉，則時刻久了就簡單構成抱軸。

1. It may be caused by the water inlet pipe and flushing position of the mixing machine. If the direction of flushing point and flushing direction are incorrect, or the flushing pressure is too low, so that the concrete temporarily bonded to the shaft cannot be washed away after the water enters the main engine, then the shaft holding will be simply formed after a long time.

2.可能是質料投料方位問題。拌和混凝土所用的物料主要是砂石骨料、水泥、粉煤灰、水和外加劑等。質料水泥若包裹砂石遇水結塊，假如拌和不充沛就簡單粘在拌和軸上，若水泥進料口方位方向不合理，使拌和軸不能快速充沛拌和，就簡單構成抱軸現象。

2. It may be the material feeding direction. The materials used for mixing concrete are mainly sand aggregate, cement, fly ash, water and additives. If the material cement is wrapped with sand and gravel and agglomerates when encountering water, it will simply stick to the mixing shaft if the mixing is not sufficient. If the direction of the cement feed inlet is unreasonable, so that the mixing shaft can not be quickly and sufficiently mixed, it will simply form the phenomenon of shaft holding.

3.在結束作業之后沒有及時對拌和機內部進行清洗，或清洗不干凈，導致拌和軸外表仍有殘留的混凝土，枯燥后凝固在拌和軸上，假如長期如此則十分簡單發生抱軸現象。

3. After the completion of the operation, the internal part of the mixer is not cleaned in time, or the cleaning is not clean, resulting in the residual concrete on the surface of the mixing shaft, which solidifies on the mixing shaft after being dry. If this is the case for a long time, the phenomenon of holding the shaft is very simple.

自動攪拌車悶機跳閘原因：

Reasons for the trip of the automatic mixer:

1.投料過多，引起拌和機負荷過大。

1. Excessive feeding causes excessive load of the mixer.

2.三角傳動皮帶太松，使傳動體系功率低。

2. The triangular transmission belt is too loose, resulting in low power of the transmission system.

3.拌和主機上蓋安全檢修開關被振松，引起停機。

3. The safety maintenance switch on the upper cover of the mixing host is loosened, causing the shutdown.

4.拌和體系葉片與襯板之間的空隙過大，拌和過程中，增大了阻力。

4. The gap between the blade and the lining plate of the mixing system is too large, which increases the resistance during the mixing process.

自動攪拌車存在抱軸及悶機跳閘現象的原因就找到了，注意在平常使用中的每日檢查以及定期維護，更多相關事項就來我們網站http://www.sansungmobile.cn咨詢吧！

The reason for the phenomenon of axle holding and machine blocking tripping of the automatic mixer has been found. Pay attention to the daily inspection and regular maintenance in normal use. More relevant matters can be found on our website http://www.sansungmobile.cn Consult!