水泥自上料攪拌車由于功能性能優越，因此應用范圍越來越廣泛，但是在使用期間也會出現各種問題，所以需要提前進行了解到，比如說水泥自上料攪拌車裝載問題，這要怎么操作？
Cement self-feeding mixer is more and more widely used because of its superior function and performance, but there will be various problems during the use, so it is necessary to understand in advance, such as the loading problem of cement self-feeding mixer, how to operate this?
水泥自上料攪拌車裝載時連接緊急驅動軟管，依靠其它攪拌車的動力。驅動拌筒旋轉并將混凝土排出。但是若減速器同時發生故障時，則不可采用此法。準備好一根緊急驅動軟管，卸下接管和接頭蓋；將故障水泥自上料攪拌車的發動機熄火；將緊固螺母朝左旋松；再將旋鈕朝右旋轉，直到不能再旋為止；將高壓軟管從馬達接頭處卸下；
When the cement is loaded from the loading mixer, connect the emergency drive hose and rely on the power of other mixer trucks. Drive the drum to rotate and discharge the concrete. However, if the reducer fails at the same time, this method cannot be used. Prepare an emergency drive hose, remove the nozzle and joint cover; The engine of the mixing car of the faulty cement is flameout. Unscrew the fastening nut to the left; Turn the knob to the right until it can no longer turn; Unload the high pressure hose from the motor joint;
將操作手柄至于空檔位置；將發動機熄火；將高壓軟管從高壓油管處卸下；將緊急驅動軟管接到高壓油管上；用緊急驅動軟管上的接頭蓋將驅動車的高壓軟管蓋起，以防漏油。啟動水泥自上料攪拌車的發動機。將水泥自上料攪拌車的操作手柄撥至“出料”位置，使故障車內的混凝土排出。緊急驅動完畢后，使兩車各自恢復原狀。
The operating handle to the neutral position; Turn off the engine; Unload the high-pressure hose from the high-pressure tubing; Connect the emergency drive hose to the high-pressure tubing; Cover the high pressure hose of the drive truck with the connector cover on the emergency drive hose to prevent oil leakage. Start the engine of the cement self-feeding mixer. Move the cement from the operation handle of the mixing truck to the "discharging" position, so that the concrete in the car with failure is discharged. After the emergency drive, restore the two cars to their original shape.
為了提高水泥自上料攪拌車的工作效率，以上裝載等問題就需要多了解誒，此外還要知道一個問題--堵料，這也是常見的問題，原因之一便是水泥自上料攪拌車因料倉內無法加裝料位機，所以基本都有時間控制。
In order to improve the working efficiency of cement self-feeding mixer, the above loading and other problems need to be understood. In addition, we also need to know a problem -- material blocking, which is also a common problem. One of the reasons is that the cement self-feeding mixer cannot be equipped with a material level machine in the bin, so it basically has time control.
如何設置時間參數，上下料時間設置還是比較簡單的，在初次使用時，先設置一個比較短的時間，然后根據每次吸料位置慢慢加，當達到料位達到吸料口的時間，再減去一秒就是合理時間。放料時間是確保放完料再加一秒。
How to set the time parameters, the loading and unloading time setting is relatively simple, in the first use, set a relatively short time, and then according to each suction position slowly add, when the material level to reach the suction mouth time, then minus a second is a reasonable time. Discharging time is to ensure the discharging of the material plus one second.
正確的方式是物料在吸料口和空氣形成一定的氣物混合比，在氣流推動下均勻流入上料機。這個時候我們需要將料倉設計帶有補氣功能。如果物料積壓時間過長可能會很硬，這個時候需要在料倉上裝一個振蕩器，敲碎結塊的物料。
The correct way is that the material in the suction port and air to form a certain air mixture ratio, under the impetus of air flow into the feeding machine. At this time we need to design the bin with qi function. If the material backlog time is too long, it may be very hard. At this time, an oscillator needs to be installed in the bin to break the lumped material.
The concrete operation of the loading problem of the cement mixing truck and the understanding of other problems are here. If you still want to know more problems, come to our website www.sansungmobile.cn to consult customer service staff.
上一篇：水泥自動攪拌車的攪拌主機“抱軸”如何處理？
下一篇：自上料水泥攪拌車的維護工作以及選購原則
