自動攪拌車堵管了如何解決？在一邊進行泵送一反泵操作，一邊沿管路檢查時，可以用小錘敲打被認為是堵塞的部位，有時可使堵塞的骨料瓦解而恢復暢通:若敲打無效，則不準再用鐵錘或其他可能傷害管道的物件重擊。

How to solve the pipe blockage of the automatic mixer? When carrying out pumping and reverse pumping operation while checking along the pipeline, you can use a small hammer to knock the part that is considered to be blocked, sometimes it can make the blocked aggregate disintegrate and restore the smoothness. If the knocking is invalid, you can not use a hammer or other objects that may damage the pipeline.

如果堵塞部位判斷得準確，而且堵塞處離管道卸料的末端不遠時，只要把堵塞段管件拆下，清除其中已堵塞的混凝土，再裝回去，即可繼續泵送。

If the blocked position is judged accurately and the blocked position is not far from the end of the pipe discharge, the pumping can continue as long as the pipe fittings in the blocked section are removed, the blocked concrete is removed, and then installed back.

堵管部位在管道拆開時很容易判斷;只要進行泵送操作，從拆開的管口有混凝土流出，則說明拆開部位與棍凝土輸送泵之間無堵塞，應繼續檢查直至找到堵塞部位。如果堵管部位離管道端較遠，堵塞段被清理后回裝到管路，由于這段空管的氣塞作用，也會造成再次堵塞。在這種情況下，應將堵塞段以后的管道混凝土用壓縮空氣吹出再接管泵送。如果堵管部位不能迅速判斷或者難以拆卸時，應采用氣洗方法把混凝土吹除，在堵管的情況下，往往需要分段吹洗。

The pipe plugging position is easy to judge when the pipe is disassembled; As long as the pumping operation is carried out and there is concrete flowing out from the dismantled pipe orifice, it means that there is no blockage between the dismantled part and the rod concrete delivery pump, and the inspection shall continue until the blockage is found. If the pipe plugging position is far away from the pipe end, the blocked section will be cleaned and reinstalled into the pipeline. Because of the air plug effect of this empty pipe, it will also be blocked again. In this case, the pipe concrete after the blocked section shall be blown out with compressed air and then pumped. If the pipe plugging position cannot be determined quickly or is difficult to remove, the concrete shall be blown out by air washing method. In case of pipe plugging, it is often necessary to blow out in sections.

若分成較短的管段也吹洗不動時，要盡快組織人力，把全部管道逐節拆卸，清除其中的混凝土，并用水沖洗干凈。

If the pipe is divided into shorter sections and cannot be purged, manpower shall be organized as soon as possible to dismantle all the pipes section by section, remove the concrete in them, and wash them with water.

自動攪拌車堵管的原因以及處理的方法就是上面這些，大家在發現自動攪拌車的管堵了千萬不要慌張，大家可以使用上面這些方法來解決。如果還有不明白的問題歡迎來電詳詢http://www.sansungmobile.cn。

These are the reasons for the pipe blockage of the automatic mixer and the treatment methods. Don't panic when you find the pipe blockage of the automatic mixer. You can use these methods to solve it. If you have any questions you don't understand, please call us for details http://www.sansungmobile.cn 。